收藏本站
DATA SHEET
8.7
PSON_L INPUT
The PSON_L is an internally pulled-up (3.3 V) input signal to enable/disable the main output V 1 of the front-end. This active-
low pin is also used to clear any latched fault condition. The timing diagram is given in Figure 29 and the parameters in
Table 5 .
Table 5 - PSON_L timing
OPERATING CONDITION
MIN
MAX
UNIT
t PSON_L V1on
t PSON_L V1off
t PSON_L H min
PSON_L to V 1 delay (on)
PSON_L to V 1 delay (off)
PSON_L minimum High time
2
2
10
20
20
ms
ms
ms
8.8
PWOK_H SIGNAL
The PWOK_H is an open drain output with an internal pull-up to 3.3 V indicating whether both V SB and V 1 outputs are within
regulation. This pin is active-low. The timing diagram is shown in Figure 26 / Figure 29 and referenced in the Table 6 .
Figure 29 - PSON_L turn-on/off timing
Table 6 - PWOK_H timing
OPERATIN G CONDITION
MIN MAX UNIT
t PWOK_H del
PWOK_H to V 1 delay (on)
100 500
ms
PWOK_H to V 1 delay (off)
AC
Input
caused by:
PSKILL_H
PSON_L, ACOK_H, OT, Fan
0
1
1
2.5
ms
ms
V SB
t PWOK_H warn*) Failure
V 1
PSON_L
t PSON_L V1on
t V1 rise
t PSON_L H min
t PSON_L V1off
UV and OV on VSB
OC on V1 (Software trigger)
OC on V1 (Hardware trigger)
OV on V1
1
-11
-1
-3
30
0
0
0
ms
ms
ms
ms
ACOK_H
*) A positive value means a warning time, a negative value a
PWOK_H
8.9
t PWOK_H del
CURRENT SHARE
t PWOK_H warn
delay (after fact).
The PFE front-ends have an active current share scheme implemented for V 1 . All the ISHARE current share pins need to be
interconnected in order to activate the sharing function. If a supply has an internal fault or is not turned on, it will disconnect
its ISHARE pin from the share bus. This will prevent dragging the output down (or up) in such cases.
The current share function uses a digital bi-directional data exchange on a recessive bus configuration to transmit and re-
ceive current share information. The controller implements a Master/Slave current share function. The power supply provid-
ing the largest current among the group is automatically the Master. The other supplies will operate as Slaves and increase
their output current to a value close to the Master by slightly increasing their output voltage. The voltage increase is limited to
+250 mV.
The standby output uses a passive current share method (droop output voltage characteristic).
8.10 SENSE INPUTS
Both main and standby outputs have sense lines implemented to compensate for voltage drop on load wires. The maximum
allowed voltage drop is 200 mV on the positive rail and 100 mV on the PGND rail.
With open sense inputs the main output voltage will rise by 270 mV and the standby output by 50 mV. Therefore if not used,
these inputs should be connected to the power output and PGND close to the power supply connector. The sense inputs are
protected against short circuit. In this case the power supply will shut down.
8.11 HOT-STANDBY OPERATION
The hot-standby operation is an operating mode allowing to further increase efficiency at light load conditions in a redundant
power supply system. Under specific conditions one of the power supplies is allowed to disable its DC/DC stage. This will
save the power losses associated with this power supply and at the same time the other power supply will operate in a load
range having a better efficiency. In order to enable the hot standby operation, the HOTSTANDBYEN_H and the ISHARE pins
need to be interconnected. A power supply will only be allowed to enter the hot-standby mode, when the HOT-
STANDBYEN_H pin is high, the load current is low (see Figure 30 ) and the supply was allowed to enter the hot-standby
mode by the system controller via the appropriate I 2 C command (by default disabled). The system controller needs to ensure
that only one of the power supplies is allowed to enter the hot-standby mode.
PFE1100-12-054xA
12
www.power-one.com
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
PFE500S-28/T PWR SUP AC/DC 85-265VAC 28V
PFE700S-48 PWR SUP AC-DC 85-265VAC 51V 14A
PFE850-12-054RA FRONT END 850W 12V HI EFFICIENCY
PGB1040805NR SUPPRESSOR ESD 24VDC 0805 SMD
PGB2010402KRHF SUPPRESSOR ESD 12VDC 0402 SMD
PHW603616 BOX FIBER 63.5X36.5X18.1" GREY
PI-1902 BOX ABS 1.26" X 1.97" X 3.54"GRY
PI-1905 BOX ABS 1.97" X 2.36" X 4.72"GRY
相关代理商/技术参数
PFE1100-12-054RA 功能描述:FRONT END 1100W 12V HI EFFICINCY RoHS:是 类别:电源 - 外部/内部（非板载） >> AC DC 转换器 系列:* 产品培训模块:MP Modular-Configurable AC-DC Power Supply 特色产品:Configurable Power Supplies 标准包装:1 系列:MP
PFE1100-12-054RD 制造商:Power-One 功能描述:- Trays 制造商:Power-One 功能描述:Power One PFE1100-12-054RD DC to DC
PFE-12 制造商:FAIRFORD ELECTRONICS 功能描述:SOFTSTARTER PFE-12 22A 制造商:FAIRFORD ELECTRONICS 功能描述:SOFTSTARTER, PFE-12 22A 制造商:FAIRFORD ELECTRONICS 功能描述:SOFTSTARTER, PFE-12 22A; Supply Voltage Range:230V AC to 460V AC; No. of Phases:Three; Power Rating:15hp; Current Rating:22A; Operating Temperature Min:0C; Operating Temperature Max:40C; Approval Bodies:IEC; Control Voltage DC ;RoHS Compliant: NA
PFE12HSX-U 功能描述:线性和开关式电源 240W 12V 36A RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度:
PFE12HSX-U1 功能描述:线性和开关式电源 240W 12V 36A RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度:
PFE12HSX-U-P 功能描述:线性和开关式电源 240W 12V W/COVER RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度:
PFE1300-48-054NA 功能描述:POWER SUPPLY FRONT END 1.3KW FAN 制造商:bel power solutions 系列:PFE1300 零件状态:有效 类型:前端 输出数:1 电压 - 输入:90 ~ 264 VAC 电压 - 输出 1:48V 电压 - 输出 2:- 电压 - 输出 3:- 电压 - 输出 4:- 电流 - 输出（最大值）:26.8A 功率（W）:1300W 应用:ITE（商业） 电压 - 隔离:4.242kV（4242V） 效率:94% 工作温度:0°C ~ 45°C 特性:可调输出，热插拔，I2C? 接口，负载均分，PFC，PMBus?，远程开/关，遥测，待机输出 安装类型:机架安装 大小/尺寸:12.66" 长 x 2.15" 宽 x 1.57" 高（321.5mm x 54.5mm x 40.0mm） 所需最小负载:- 认可:CB，cCSAus，CE，NEMKO 功率（W） - 最大值:1286W 标准包装:30
PFE-14 制造商:FAIRFORD ELECTRONICS 功能描述:SOFTSTARTER PFE-14 30A 制造商:FAIRFORD ELECTRONICS 功能描述:SOFTSTARTER, PFE-14 30A 制造商:FAIRFORD ELECTRONICS 功能描述:SOFTSTARTER, PFE-14 30A; Supply Voltage Range:230V AC to 460V AC; No. of Phases:Three; Power Rating:20hp; Current Rating:30A; Operating Temperature Min:0C; Operating Temperature Max:40C; Approval Bodies:IEC; Control Voltage DC ;RoHS Compliant: NA